Arduino has moved the Nano form factor onto the factory floor. The Nano XL Link, unveiled on 10 November 2026 at electronica in Munich, is a Nano-format board built on a Microchip PIC32CK microcontroller. It carries CAN FD, RS-485 and 10/100 Ethernet hardware on the board, and a second row of header pins takes it past the classic Nano pinout. It ships alongside a Nano XL Link Connector Carrier, a DIN-rail-mountable base board with screw terminals and an RJ45 jack, which Arduino also describes as a reference design. Hackster.io reports that the pair is "not yet available to buy" and that no pricing or availability had been announced.
Hackster quotes the Arduino team as saying the new boards are designed to take everything the Nano does well "into a new territory: industrial, home, and building automation." The parts list backs that up. This is a fieldbus node first and a general-purpose Nano second.
The microcontroller
According to Arduino's documentation, the board uses the Microchip PIC32CK2051SG01144, a 32-bit Arm Cortex-M33 part with 2 MB of flash, 512 kB of RAM and an integrated hardware security module (HSM). Hackster gives the core clock as up to 120 MHz. That figure comes from Hackster's report, not from the Arduino documentation we read.
The software choice matters as much as the silicon. The Nano XL Link is programmed with the Arduino Zephyr core, not a bare-metal Arduino core. Zephyr is what provides the board's Ethernet networking, as described below. A PIC32CK under Zephyr is a long way from the AVR Nanos most hobbyists started on.
Three fieldbuses on one Nano
Arduino lists three interface ICs on the board. We checked each against its manufacturer's datasheet.
- CAN FD: Texas Instruments TCAN3414. Arduino says the board supports classic CAN and CAN FD, with payloads up to 64 bytes at up to 8 Mbps. TI's TCAN3413/TCAN3414 datasheet describes a 3.3 V CAN FD transceiver that is compatible with the physical-layer requirements of ISO 11898-2:2016 and supports classical CAN plus CAN FD at 2, 5 and 8 Mbps. It is rated for ±58 V bus fault protection and ±10 kV IEC ESD on the bus pins. Both variants have a low-power standby mode; the TCAN3414 adds an ultra-low-power shutdown mode.
- RS-485: Texas Instruments THVD2410. This is a half-duplex transceiver. Arduino supports it through the ArduinoRS485 library and names Modbus RTU as a target protocol. TI's THVD2410/THVD2450 datasheet lists ±70 V fault protection, a 3 V to 5.5 V supply, a -40 °C to 125 °C ambient range and compliance with TIA/EIA-485A. The THVD2410 is the 500 kbps part; its sibling, the THVD2450, runs to 50 Mbps. The datasheet therefore puts the RS-485 transceiver's data rate at 500 kbps. That suits Modbus RTU, but anyone planning faster RS-485 links should keep it in mind.
- Ethernet: KSZ8081RNAIA PHY. This gives 10/100 Ethernet through the Zephyr network stack, which Arduino says covers IPv4, TCP, UDP, DHCP and DNS. The RJ45 jack and magnetics are not on the Nano XL Link. They sit on the Connector Carrier, so the board alone has an Ethernet PHY but no socket to plug a cable into.
CAN and RS-485 bus termination are set with solder jumpers, according to Arduino's documentation. Termination is a soldering job, not a software setting.
One mismatch is worth flagging. The transceiver datasheets list wide temperature ranges, but Arduino rates the finished board for -20 °C to +85 °C, so -20 °C is the lower limit for the board as a whole.
Pinout: Nano-compatible, then some
The board has two 2x15 headers. Arduino says they keep the classic Nano pins and add a second row that carries 12 extra digital pins, a second SPI bus, an I2C bus, a second UART, I2S and the fieldbus lines. A Qwiic connector provides 3.3 V I2C for solderless sensor modules.
The second row has a cost. Hackster notes that the extra row of pins on each side means the board is no longer breadboard-compatible once those headers are fitted. If you use the board with only the outer row populated, it behaves like a Nano. Fit the full 2x15 headers and it no longer sits in a standard breadboard.
Power
Arduino's documentation lists three ways to power the board: USB-C, +7 to 24 VDC on VIN through an onboard buck converter, or a regulated +3.3 VDC on the 3V3 pin.
The Connector Carrier
The Connector Carrier documentation describes a DIN-rail-mountable board that serves as both a carrier and a reference design. Hackster describes it as 4U DIN-mountable. Arduino lists the following:
- Screw terminals for RS-485 and CAN bus
- An RJ45 Ethernet port, which provides the jack and magnetics the Nano XL Link itself lacks
- A 2x4 female header for an ESP8266 (ESP-01) Wi-Fi module
- An onboard Qwiic connector
- Dual 2x20 breakout headers
- A 2x5, 1.27 mm SWD connector for hardware debugging
- A Power IN screw terminal accepting +7 to 24 V, with reverse-polarity and TVS protection
The ESP-01 header is an unusual choice. Arduino has not added a radio to the main board and instead leaves Wi-Fi as an optional plug-in module on the carrier. The SWD header means you can attach a debug probe without modifying the Nano.
What It Means for Makers
The Nano XL Link is aimed at people building controllers for industrial, building and home automation, which is Arduino's own framing. It is a good fit for a Modbus RTU node that reads an energy meter or HVAC controller, a CAN FD logger or gateway, or a small Ethernet-connected device on a DIN rail beside other modular equipment. Until now, a Nano-class project like that usually meant stacking separate transceiver breakouts and an Ethernet module, then designing your own terminal board. Here the transceivers, the PHY and a reference carrier are all included, and the HSM gives a hardware basis for secured devices.
It is not a straight replacement for a breadboard Nano. With the full headers fitted it no longer fits a breadboard, and the Zephyr-based toolchain will be unfamiliar to anyone used to the classic AVR cores. Educators and hobbyists who just need GPIO have cheaper, simpler options. The case for this board rests on the fieldbus hardware.
Status: announced, not on sale. Hackster reported on 10 November 2026 that the boards are not yet available to buy and that no pricing or availability had been announced. The hardware was on display at the Qualcomm booth, Hall C5 Booth #439, at electronica 2026. We will update this article when Arduino publishes pricing and a ship date.