MikroTik has added Wi-Fi HaLow to its KNOT line of IoT gateways. The new KNOT Gateway HL9 (product code L14G-2ax-BT5-HL9&EG800Q) is a weatherproof box that puts five kinds of wireless in one IP66 enclosure: a 915 MHz Wi-Fi HaLow radio, Bluetooth Low Energy 5.1, 2.4 GHz Wi-Fi, LTE Cat 1 bis and GNSS. It also has one Gigabit Ethernet port with PoE-in. MikroTik's product page lists a suggested price of $139.00, and Hackster.io reports that price includes a PoE injector and a power adapter.
The HaLow radio uses silicon from Morse Micro. The Morse Micro newsroom lists a press release dated November 5, 2026, titled "MikroTik Launches Wi-Fi HaLow Outdoor Gateway with Morse Micro Silicon". Its summary describes the HL9 as a gateway "with IP66 protection, LTE backhaul, and GPS for sites with no wired connection." Hackster.io, reporting on the launch, calls it MikroTik's first outdoor IoT gateway with Wi-Fi HaLow. Hackster also reports that the HL9 is available to order from resellers.
What the HL9 is for
Wi-Fi HaLow is IEEE 802.11ah. It is the sub-GHz branch of the Wi-Fi family, aimed at sensors and other low-rate devices that ordinary 2.4 GHz and 5 GHz Wi-Fi does not serve well. On the HL9, MikroTik pairs that radio with two other ways to talk to nearby devices: BLE 5.1 for beacons and battery-powered tags, and a single-chain 2.4 GHz 802.11ax radio for standard Wi-Fi clients. For the uplink you can use the Gigabit Ethernet port, or the LTE modem where no cable exists. GNSS supplies location.
That combination matches how Morse Micro's newsroom describes the product: a gateway for sites with no wired connection. MikroTik's hardware manual says the product is intended to be installed outdoors, on a wall or pole. Gather readings over HaLow or BLE and send them out over LTE. MikroTik's product page lists RouterOS scripting plus MQTT and HTTP publishing. That means the gateway can push data to a broker or web endpoint on its own, without a separate computer at the site.
The HL9 is not the only version. MikroTik's page and Hackster.io both note that the KNOT Gateway is also sold as the KNOT Gateway LR8, which uses an 868 MHz LoRa radio in place of HaLow. The model names follow the radio: HL for HaLow, LR for LoRa, plus the band.
The spec sheet, as MikroTik lists it
All figures below come from MikroTik's KNOT Gateway HL9 product page unless noted otherwise. MikroTik's hardware manual for the L14G-2ax-BT5-HL9&EG800Q also lists the 915 MHz HaLow radio and BLE 5.1.
- Processor: IPQ-5010, ARM64, 2 cores at 800 MHz. Hackster.io names it as a Qualcomm part.
- Memory and storage: 256 MB RAM, 128 MB NAND.
- Operating system: RouterOS v7, license level 4.
- Sub-GHz radio: Wi-Fi HaLow (IEEE 802.11ah), 915 MHz, using Morse Micro silicon (per the Morse Micro newsroom).
- Wi-Fi: 2.4 GHz 802.11b/g/n/ax, 1 chain, 287 Mbit/s maximum data rate, 3.9 dBi antenna gain.
- Bluetooth: BLE 5.1.
- Cellular: LTE Cat 1 bis, 10 Mbps down and 5 Mbps up, bands 2/4/5/12/13/66.
- SIM: one nano SIM slot plus eSIM.
- Positioning: GNSS.
- Wired networking: one 10/100/1000 Ethernet port.
- Power input: DC 12–57 V, or PoE-in (802.3af/at) at 18–57 V.
- Maximum power consumption: 7 W.
- Enclosure: IP66.
- Tested ambient temperature: -40 °C to 50 °C.
- Certifications: FCC, IC, EAC.
- In the box: 24 V 0.5 A power adapter, Gigabit PoE injector, hose clamp, and K-66 fastening set.
- Suggested price: $139.00 (MikroTik product page, at launch).
Some things are missing from MikroTik's page and the other sources: the exact Morse Micro chip and HaLow throughput or range. PinoutFeed won't fill those gaps with guesses. Anyone planning a deployment should check the hardware manual and confirm those details with MikroTik or a reseller.
Reading the numbers
The LTE modem is Cat 1 bis, with a listed peak of 10 Mbps down and 5 Mbps up. That suits telemetry. It does not suit video backhaul, and it is not meant to. Cat 1 bis is a single-antenna LTE category built for IoT, and the bandwidth here fits a box whose job is to collect small payloads from many devices. The Wi-Fi radio has one chain and a rated 287 Mbit/s, so it is also a convenience link rather than a performance one. Expect to use it for setup or for a few local clients, not as an access point for heavy traffic.
The power figures matter more for mounting the box than for anything else. The HL9 draws 7 W at most, and it accepts 802.3af/at PoE as well as a wide 12–57 V DC input. So it can run from the bundled injector, from an existing PoE switch, or from a DC supply already at the site. MikroTik ships the 24 V 0.5 A adapter and the injector in the box. Combined with the hose clamp and K-66 fastening set, you can mount and power the $139 package without buying anything else.
On the compute side, a dual-core 800 MHz ARM64 chip with 256 MB of RAM is modest. It is enough for RouterOS, its scripting engine, and MQTT or HTTP publishing, which are the features MikroTik lists for this product. The 128 MB of NAND is enough storage for the operating system and scripts. It is not enough to make the gateway a general-purpose Linux edge computer, and MikroTik does not pitch it that way.
The 915 MHz HaLow band, the FCC and IC certifications, and the LTE bands listed above all suggest the HL9 targets North American deployments. That is our inference. MikroTik's page does not state a region. The 868 MHz LoRa version (LR8) covers a different band. Check that the radio band and certifications are right for your country before you buy.
What It Means for Makers
The HL9 is aimed at people who already have sensors in the field and need a weatherproof box to gather their data and send it home. Typical users would be makers with farm, greenhouse or property-monitoring projects, educators running outdoor sensor labs, and embedded engineers testing 802.11ah client hardware who need an access point that works without extra setup. Until now, such a setup usually meant a single-board computer with a HaLow module and an LTE modem, plus a sealed enclosure and power arrangements to build yourself. The HL9 puts HaLow, BLE, LTE backhaul, GNSS and PoE into one IP66 unit, and configuration happens in RouterOS rather than in your own software stack.
There are trade-offs. The setup model is RouterOS, so people who don't know MikroTik's tools will have something to learn. The CPU and storage are sized for a gateway, not for running your own applications. HaLow throughput and range are not stated in the sources reviewed here, so test it at your own site before relying on it.
Price and availability: MikroTik lists a suggested price of $139.00 at launch, and Hackster.io reports that it includes the PoE injector, the 24 V 0.5 A adapter and the mounting hardware. Morse Micro's newsroom dates the launch press release November 5, 2026, and Hackster.io reports the gateway is available to order from resellers. If you need LoRa instead of HaLow, the sibling KNOT Gateway LR8 has an 868 MHz LoRa radio.