Cheap USB logic analyzers have long tended to be 8-channel boards built around a USB 2.0 bridge chip and run by Sigrok and PulseView. WeAct Studio's new Logic Analyzer V2 takes a different approach. It is built on WCH's dual-core RISC-V CH32H417 microcontroller, it captures over USB 3.0, and the same small board can boot into a debug probe or into firmware you write yourself. CNX Software reported the board on 12 November 2026 and said WeAct sells it on AliExpress for about $10 plus shipping and taxes.

WeAct's official GitHub repository sums the product up in one line: "200 MHz, 16-channel logic analyzer. CH32H417 dual-core, USB 3.0 Type-C." The details below come from that README unless another source is named.

The silicon

According to CNX Software, the WCH CH32H417 pairs a QingKe RISC-V5F core running at up to 400 MHz with a QingKe RISC-V3F core running at up to 144 MHz. It also has a GPHA graphics accelerator, 896 KB of SRAM and 960 KB of flash. WeAct's board is not the first to use the chip. In May 2026, CNX Software covered MuseLab's nanoCH32H417 development board, listed from $17 on the company's Tindie store, and noted the part's USB 3.0 (5 Gbps), UHS and Fast Ethernet support. The USB 3.0 interface is the part a logic analyzer needs. WeAct's README says the Type-C connector goes to the chip's on-chip USB 3.0 (SuperSpeed) port, which is how the board can stream samples to the PC at rates beyond what USB 2.0 allows.

Three firmware images, one button

WeAct splits the flash into fixed regions and calls the firmware images "apps." According to the README, the map is:

  • IAP bootloader: the first 24 KB, starting at 0x08000000.
  • Slot 0 (0x08006000): the logic analyzer (200 MHz, 16 channels).
  • Slot 1 (0x08052000): USB-serial plus DAP, which provides three CDC serial ports at up to 9 Mbps and a CMSIS-DAP v2 SWD probe.
  • Slot 2 (0x0809E000): "your own app," a 304 KB slot for user firmware built with WeAct's SDK.
  • Configuration: the last 24 KB, at 0x080EA000.

The key on the board switches between apps. The README says you hold it for 2 seconds until the LED turns white, then release, and a single WS2812 RGB LED reports the current state by colour. One board can therefore act as a logic analyzer in one bench session and as an SWD debugger with three serial consoles in the next, without reflashing from a host. The repository's Slot2_Example folder holds a starting point for custom firmware. CNX Software notes that the example uses the MounRiver IDE.

Analyzer specifications

These figures come from WeAct's README:

  • Channels: 16 (D0–D15), configurable as 2, 4, 8 or 16.
  • Sample rate over USB 3.0: 4–200 MHz.
  • Sample rate over USB 2.0: 4–20 MHz with 16 channels, or 4–40 MHz with 8 channels.
  • Capture length: from 10 ms upward. The ceiling is PC memory: about 45 s at 200 MHz with 16 channels, or 90 s with 8 channels.
  • Input level: adjustable from 1.0 to 3.3 V, with a 0.6–1.5 V threshold.
  • Protocol decoders: 132, including UART, I2C, SPI and CAN.
  • Interface and power: USB 3.0 Type-C, with a 5 V input.
  • Size: 42.5 × 26.5 × 13 mm with its enclosure.

CNX Software adds that the board has a 20-pin header with 16 GPIO and 4 ground pins.

The USB 2.0 figures matter. The 200 MHz headline applies only when the board is on a USB 3.0 connection. On USB 2.0, the README's ceiling is 20 MHz with all 16 channels, or 40 MHz with 8. CNX Software says the USB-C cable is optional when you order, so check that the cable you use supports USB 3.0. The README also warns that other devices on the same USB controller can interrupt a capture, and suggests dropping to 8 channels at 200 MHz or 16 channels at 100 MHz.

Captures are held in PC memory, so WeAct's 45-second figure at full rate depends on how much RAM the PC has, not on the board. The README says the software works from an 18 GB ceiling and stops early when memory runs low.

200 MHz of what?

A commenter on CNX Software's article argued that the 200 MHz figure is a maximum sample rate and does not equal 200 MHz of bandwidth, and estimated the realistic figure at around 50 MHz (theoretically 100 MHz because of Nyquist). That estimate comes from a reader, not from WeAct, whose README publishes no analog bandwidth or input-stage figures. The general point holds for any logic analyzer, though: you need several samples per bit period to measure edges and timing reliably, so the usable bus speed is well below the sample rate. For the I2C, SPI, UART and CAN traffic most makers debug, this matters little. For fast parallel buses or high-clock SPI flash, it does.

Software: a PulseView fork, closed firmware

The host application is U3LogicAnalyzer, a Sigrok/PulseView-based program for Windows and Linux. CNX Software says it is a fork and speculates that WeAct did not upstream support because the Sigrok project appears dormant. Firmware updates run from the application's Help > FW Update menu, according to the README. CNX Software also lists two companion tools: CH32H417_LogicAnalyzer_Upgrade and WeActStudio.DAPFlasher.

The main limitation is openness. CNX Software reports that the logic analyzer and DAP firmware are distributed only as closed-source binaries. The repository has Doc, Firmware, Images and Slot2_Example folders, and at the time of writing it showed 15 stars. If you want to change the capture engine, inspect how the probe firmware works, or depend on the tool long term, you are relying on WeAct to maintain both the binaries and the PulseView-based software. The open part of the design is Slot 2, which runs your own code on the same hardware.

Not the only CH32H417 analyzer

Other makers are building on the same chip. A Hack Club gadget listing describes a "3-in-1 200MHz USB 3.1 logic analyzer, 20MHz oscilloscope and CH32H417 devboard," with a 20Msps analog component. That is a separate community design, not WeAct's board. WeAct's documentation mentions no analog capture, and the listing says "USB 3.1" where WeAct's README says USB 3.0. It is useful only as a sign that the CH32H417's SuperSpeed port is attracting makers building low-cost capture hardware.

What It Means for Makers

The Logic Analyzer V2 is aimed at people who now own an 8-channel USB 2.0 analyzer and want more channels and a longer capture window without paying for a branded instrument. It also suits anyone who wants one small device that can be a logic analyzer, an SWD debugger and a set of serial adapters. Makers already working with WCH parts get a third use: the 304 KB Slot 2 makes the board a compact CH32H417 platform with a USB 3.0 Type-C port and a 16-GPIO header.

Before buying, consider the limits. The full 200 MHz rate requires USB 3.0. On USB 2.0, the README caps it at 20 MHz with 16 channels or 40 MHz with 8. The input range is 1.0–3.3 V, so 5 V logic is outside the published specification. The analyzer and DAP firmware are closed binaries, and the host software is a PulseView-based fork that CNX Software says is not part of upstream Sigrok.

On price and availability, CNX Software reported on 12 November 2026 that WeAct sells the board on AliExpress for about $10 plus shipping and taxes, with an optional USB-C cable. A commenter there said shipping made it well over $20 (USD) in their location, so check the delivered price. WeAct's README gives no price or launch date.

Sources