The M5Stack Cardputer has picked up a large library of community firmware since it launched, and the hardware lends itself to that: a small screen, a keyboard, an audio path and an ESP32-S3 in a case that fits in a pocket. The latest firmware to get wider attention is DIVINER, which Hackaday covered on November 14, 2026. It is part synthesizer and sequencer, part visualization engine and part network utility, and it is styled throughout in what Hackaday calls "blood and ember," Diablo-esque visuals. The apps are called "rites."
Hackaday credits the project to the handle [voidrane Splicer]. The code sits in the numbpill3d/cardputer-adv-diviner repository on GitHub, and the README describes it as companion firmware for the Cardputer ADV that boots from the community bmorcelli Launcher. The repository was last pushed on 2026-11-14.
The hardware underneath
According to M5Stack's documentation for the Cardputer-Adv (SKU K132-Adv), the device is built around the Stamp-S3A core module, which uses an ESP32-S3FN8 (dual-core Xtensa LX7 at 240 MHz). M5Stack lists the rest of the hardware as follows:
- Display: 1.14-inch ST7789V2 LCD, 240 x 135
- Input: 56-key keyboard in a 4 x 14 layout, 160 gf actuation
- Audio: ES8311 codec, MEMS microphone (SNR 65 dB), NS4150B amplifier driving an 8 ohm 1 W speaker, and a 3.5 mm audio output
- Sensors and I/O: BMI270 6-axis IMU, IR emitter, microSD slot
- Expansion: HY2.0-4P Grove port and an EXT 2.54-14P bus
- Power: 1500 mAh battery
- Mechanical: magnetic back, LEGO-hole compatible
- Software support: Arduino, UiFlow2, ESP-IDF and PlatformIO
DIVINER relies on most of this. The README lists the ES8311 codec in its hardware layer, the 240 x 135 panel is the canvas for the visual rites, and the IR emitter is what the remote-control rite uses. Hackaday describes the audio side as using the I2S audio out.
Sixteen rites, four domains
The README sorts the sixteen rites into four domains: sound, sight, the wired and wards. The sound and sight domains are what make DIVINER more than another utility firmware.
Sound
The drone rite is a generative drone synthesizer. seq is a groovebox with kick, snare, hat and acid voices, Euclidean fills, four pattern banks, a song mode, and save and load. The beat rite is a bytebeat livecoder: you type a C expression in t and hear it instantly. Bytebeat is the old demoscene trick of generating audio from a short integer expression evaluated per sample, and a 56-key keyboard is a much better place to type those expressions than a touchscreen. Hackaday also lists a byte-beat player among the features.
Sight
The visual domain covers wired, an ASCII 3D renderer, plus rites named visions and oracle. Hackaday calls this side of the firmware a visualization engine, and its coverage also mentions an LLM interface. The README listing does not say which rite provides it.
The wired
The network-and-radio domain includes link, a Wi-Fi connection rite with captive-portal detection, which helps on hotel or café networks that intercept traffic before login. It also has scry and listen for Wi-Fi viewing and channel monitoring, kin for Bluetooth devices, net for mapping the LAN, and gemini, a gemtext browser that runs over TLS for the minimalist Gemini protocol. That last one suits a 240 x 135 text display well, since gemtext is line-oriented and has no layout engine to fight. banish is an IR remote supporting five protocols and uses the Cardputer ADV's onboard IR emitter.
Wards
The fourth domain groups three rites: sentinel, which learns a baseline and alarms on unknown devices, pulse, a Wi-Fi CSI motion and presence radar that the README marks as experimental, and probe, active HTTP recon with a default-credential check on an authorized host. The README carries an explicit authorized-use notice: the networked and IR rites are for networks and devices you own or are explicitly permitted to test. It also states that the project deliberately does not implement denial-of-service or phishing attacks. Makers who want to experiment with that side of the project should read the README in full and stay inside those limits.
Building, simulating and installing
DIVINER is a PlatformIO project. Per the README, the firmware target builds with pio run -e cardputer. The repository also includes a native SDL2 simulator, built with pio run -e native, that renders at the Cardputer's 240 x 135 resolution, so you can iterate on visuals and UI on a desktop without reflashing the device each time. Hackaday singles out the simulator too, and for a firmware this heavy on visuals it is likely to be useful to contributors.
Installation goes through the bmorcelli Launcher from an SD card, the usual route for community Cardputer firmware. The README warns that on the ADV, moving off the factory firmware is a full wipe, and it advises backing up the existing flash with esptool first.
What It Means for Makers
DIVINER is aimed at Cardputer ADV owners who want the device to work as a musical instrument and a visual toy, not only a terminal or a pentest-adjacent gadget. The groovebox, with four pattern banks, song mode and save/load, and the bytebeat livecoder are the main draw for anyone who has wanted a pocket sketchpad for chiptune-style ideas with a real keyboard and a 3.5 mm audio output. Educators may find the bytebeat rite a compact way to show that audio is just numbers over time, and the SDL2 simulator lets a class explore the code without a device per student.
For embedded developers, the repository is a useful worked example of one ESP32-S3 handling I2S audio, a small display, keyboard input, Wi-Fi, Bluetooth and IR in a single PlatformIO codebase with a desktop simulation target alongside it.
On cost and availability: DIVINER is free, open-source firmware. The README states an MIT license, although GitHub's license detection reports NOASSERTION for the repository, so anyone redistributing or forking it should check the license file directly. Neither the project nor the sources cited here give a price for the Cardputer ADV hardware. M5Stack's documentation lists the device as SKU K132-Adv, and buyers should check M5Stack's own store for current pricing. The firmware is available now from the GitHub repository, and its latest push was November 14, 2026. Back up your factory image before flashing, as the README advises.