Nabu Casa, the company behind Home Assistant's official hardware and a commercial partner of the Open Home Foundation, launched the Home Assistant Connect AUX-2 on November 11, 2026. The launch post calls it "available worldwide today for $69 / €59." The product page gives those figures as the recommended MSRP and notes that USD prices exclude taxes, while EUR prices include applicable taxes. It is a small ESP32-S3 box built on ESPHome. It has an audio output for the Sendspin multi-room protocol, two RS-232 ports, a USB-A port for a Z-Wave or RS-485 adapter, Bluetooth LE and Power over Ethernet.

The launch post's headline is "No device left behind," and that describes the goal. The AUX-2 is meant to bring hardware that predates the smart home, or that you don't trust on your network, under local control. According to Nabu Casa, the name stands for Audio, USB and X (serial). This article goes through what each port does, based on the official specifications and Hackster.io's independent coverage. It also notes what the ports don't do.

The silicon

The official specification page lists an ESP32-S3 SoC and a TI PCM5122 DAC rated at 112 dB SNR. Nabu Casa's page does not give memory sizes. Hackster.io reports an ESP32-S3 module with 8 MB PSRAM and 8 MB flash, plus a WIZnet W5500 Ethernet controller for the wired connection.

Per the spec page, the radios are 2.4 GHz Wi-Fi (802.11b/g/n) and Bluetooth 5 LE. The launch post also mentions an upgraded Bluetooth antenna, without giving antenna specifications.

Port by port

Audio: one output, two physical formats

The spec page lists a combined optical S/PDIF and analog 3.5 mm port. Only one can be used at a time. Both analog and digital output are rated at 16-bit / 48 kHz stereo, and the listed codecs are FLAC, MP3 and WAV. You can't run analog and optical at once to feed two systems, and the spec sheet doesn't list a high-resolution mode. The product page also says the AUX-2 has no audio input and no Bluetooth audio. For multi-room audio sent to a vintage receiver or powered speakers, 16/48 is plenty. Anyone hoping for a 24/96 streamer front end should look at the stated numbers first.

Audio streams over Sendspin, an open multi-room standard from the Open Home Foundation. The Sendspin site lists the AUX-2 as ready-made hardware at "$69 / room." It says the AUX-2 ships with Sendspin out of the box and that its 3.5mm output, analog or optical, plugs into the receiver or powered speakers you already own. Hackster notes that the box works as a Sendspin endpoint in Music Assistant. One caveat: the Sendspin site describes the protocol as being at Release Candidate 1, with the spec still being finalized. The named partners are Music Assistant, ESPHome, LedFx, AUX-2 and Voice PE. The audio feature may change while the protocol settles.

Two RS-232 ports

This is the part most likely to interest people with older gear. The spec page lists two 3.5 mm RS-232 ports, each with a TX/RX swap switch. The switch saves you from building a null-modem adapter when a cable swaps the transmit and receive lines. The 3.5 mm jacks mean you'll need a cable or adapter that matches your equipment's connector; the spec page mentions DB9, RJ9, RJ11 and MiniDIN converter cables as examples, and the box ships without serial or audio cables. The spec page and launch post don't give pinouts or supported baud rates, so check before you wire anything. The spec page also says the AUX-2 can only control serial devices that have an integration in Home Assistant.

The launch post suggests three uses for the serial ports: bring solar and climate equipment into Home Assistant over serial, control old hi-fi gear, or block a TV's internet access and control it over its serial port. That last one is a good fit for the "untrusted devices" angle. The TV stays offline, and Home Assistant drives it over a wire.

USB-A: Z-Wave or RS-485

The spec page describes the USB-A port as data for the Connect ZWA-2 Z-Wave adapter and an RS-485 adapter. Hackster names the RS-485 option as a Waveshare USB-to-RS485 adapter, and the product page notes that RS-485 needs an additional USB adapter. The port is documented for those accessories, so don't assume any USB serial dongle or storage device will work. RS-485 carries Modbus, and the product page lists HVAC systems, UPSs and solar inverters among the gear it targets.

Bluetooth proxy

The launch post says the AUX-2 can act as a Bluetooth hub, which Home Assistant calls a Bluetooth proxy, with no flashing or configuration needed. Hackster says it can proxy up to three active device connections. The product page says the antenna is for adding Bluetooth smart home devices to Home Assistant, and that it is not for Bluetooth audio.

Grove

The launch post says the Grove port offers an easy way to add sensors without opening the case. It supports GPIO and I2C sensors, whose readings show up in Home Assistant through ESPHome. The post's example is a temperature sensor watching the cooling of a UPS or power distribution unit. The sources don't give pin assignments.

Power and networking

The spec page lists two power options: USB-C at 5 V, 2 A or higher, or PoE 802.3af. The FAQ says one power source is used at a time. The launch post says PoE was added "by popular demand" and that USB power with Wi-Fi also works. The spec page carries an asterisk on its Ethernet line reading "USB-C power required," which appears to conflict with the PoE listing. If you plan a single-cable PoE install, read that footnote on the official page before ordering. The launch post also says Wi-Fi and Ethernet are alternatives, and the FAQ says wired is recommended for the most reliable link.

Physically, the spec page lists 106 x 63 x 25 mm and 104 g for the device, with indoor use only from 0 to 65 °C.

Firmware: ESPHome and an unlocked bootloader

The spec page says the AUX-2 is built on ESPHome with an unlocked bootloader, and that the device firmware "can be flashed with custom firmware." This matters as much as the port list. It means owners can reflash it with their own ESPHome configuration or other firmware. The launch post floats turning it into a dedicated Squeezelite or Snapcast streamer. For a device whose whole purpose is outliving abandoned hardware, it would be odd to ship a box that could itself be abandoned.

What It Means for Makers

The AUX-2 is aimed at Home Assistant users with a specific integration problem. That might be a receiver or TV with an RS-232 port and no network stack, a solar or HVAC system that speaks RS-485, a Z-Wave network that needs its controller somewhere other than next to the server, or an old hi-fi that should join a multi-room setup. A common DIY route for these jobs is a pile of single-purpose parts: an ESP32 dev board, a level-shifter board, a USB-to-serial cable, and a separate streaming endpoint, each with its own power supply. The AUX-2 combines those functions into one enclosed, PoE-capable box that runs firmware you can modify.

The limits, from the official spec: there is one audio output at a time, at 16-bit / 48 kHz, and no audio input. The USB-A port is documented for the ZWA-2 and an RS-485 adapter, not arbitrary USB devices. Wi-Fi is 2.4 GHz only. BLE proxying is limited to three active connections, per Hackster. Serial control only works for devices with a Home Assistant integration. Sendspin is still a release candidate. If you need more than two RS-232 lines, or want to do more with the Grove port, you'll be writing your own ESPHome configuration, which the unlocked bootloader allows.

Status and price: Nabu Casa says the Connect AUX-2 has been available worldwide since November 11, 2026, at a recommended launch MSRP of $69 (excluding tax) / €59. The product page warns that stock may be limited and that distributors' product pages are still going live. It is not a pre-order or crowdfunding campaign.

Sources