In Interstellar, TARS is a robot built from a few hinged slabs that it reshapes to walk, roll and talk. That design has been a favourite of makers for years. LuwuDynamics now sells a small desk-sized version called RIG-TARS. Its shop lists it as a "Fully Open-Source 3D-Printed Programmable AI Companion Robot Maker DIY Kit" for US$99.00. Hackster.io has covered the kit. The company's firmware repository on GitHub shows a fair amount of engineering under the film styling, and it also raises a licensing detail that buyers should check.
What you actually get for $99
The most important detail is on the product page: the kit contains electronics only. LuwuDynamics says the buyer must 3D-print the enclosure and assemble the robot. If you don't own a printer or have access to one, the $99 doesn't get you a finished robot.
On the commercial side, the shop lists RIG-TARS at US$99.00 and marks it InStock as of this writing (November 15, 2026). It says orders ship within 10 days of payment and that returns are not accepted after shipping. So this is a product in stock and shipping. It is not a crowdfunding campaign or a pre-order.
Mechanically, the shop describes three segmented upright columns driven by three servos. Moving them makes the robot step forward, step backward and turn, which is a simplified version of how the film's TARS moves. Hackster describes three articulated columns driven by UART-controlled servos. The firmware repository is more specific and lists SCS009 serial servos for its ARM and TARS builds.
The electronics, spec by spec
The three sources describe the hardware in slightly different ways, so here is each spec with its source:
- MCU: ESP32-S3, per the GitHub repository and Hackster. Neither the shop page nor Hackster gives the module variant, flash size or PSRAM. The repository's build prerequisites call for matching ESP32-S3 hardware with 16 MB flash and PSRAM.
- Display: The repository says TARS uses a 320x240 landscape display with an ST7789V2 controller. Hackster calls it a 2.4-inch 320x240 colour TFT. On the robot it shows a terminal-style status screen with voltage, posture, tasks, logs and "personality parameters" such as sincerity and humour (shop page). That last item is another nod to the film.
- Motion sensing: a QMI8658C six-axis IMU (repository). The shop says it is used for posture sensing.
- Actuators: three servos (shop), listed as SCS009 serial servos for TARS (repository).
- Audio: microphone and speaker (Hackster), on I2S audio (repository).
- Wireless: Wi-Fi and Bluetooth LE (Hackster). The firmware supports BLE control and OTA updates (repository).
- Camera: Hackster lists a camera among the robot's electronics, and the firmware supports an optional GC0308 or OV2640 camera (repository). The shop page's feature list doesn't mention one, so confirm with the seller that the kit you order includes it.
The shop page, Hackster and the repository summary don't give battery chemistry, capacity, charging method or runtime. Read the official documentation at wiki.xgorobot.com, which the shop names as the docs source, before you plan anything about power.
One firmware, four robots
The firmware is the most interesting part of the project. RIG-Omni is written in C++ on ESP-IDF and targets four robot designs from the same ESP32-S3 codebase: Puppy, Hover, ARM and TARS. TARS is the outlier on the display side. The other three use a 240x240 round GC9A01 panel, while TARS uses the rectangular 320x240 ST7789V2.
The repository splits the voice pipeline into local and cloud parts. Wake-word detection runs on the device. Speech recognition and speech generation use network services. In practice the robot can listen for its wake word on its own, but conversation needs a working Wi-Fi connection and depends on whatever back end the firmware uses. Hackster also describes the LLM conversation as cloud-connected. The sources don't say who runs the speech and LLM services, what they cost after purchase, or how long they will stay available. Anyone planning a long-lived classroom deployment should ask those questions first.
The repository also lists MCP tools support, and Hackster describes it as Model Context Protocol support that lets the robot connect to external services. In the repository's own description, the tools are voice-callable: movement, calibration, status and TARS personality controls. The shop page also mentions an action library and expression logic that can be called to create different character behaviors.
According to the GitHub API, the last push to the repository was on October 1, 2026.
About "fully open source"
The product title says "Fully Open-Source." Hackster reports that the RIG-Omni firmware, mechanical designs and documentation are released as open source. The repository's README states that the project is licensed under the Apache License, Version 2.0, with a copyright line for "RIG-Omni Contributors." However, the GitHub API's license field for the repository is null, meaning GitHub hasn't detected a standard license file, so the README statement may not be backed by a LICENSE file in the repository.
For a hobbyist flashing their own robot, this probably doesn't matter. For an educator building a curriculum, or a maker planning to sell remixes or derivative firmware, it is worth a few minutes. Check the repository for a LICENSE file, and if it's missing or unclear, ask LuwuDynamics directly before relying on the "open source" label. We did not verify the licensing of the mechanical designs or documentation.
What It Means for Makers
Who it's for: people who already own a 3D printer and want a character robot with a real embedded stack under it. You get an ESP-IDF C++ codebase, serial servos instead of PWM hobby servos, an IMU, an I2S audio path and BLE/OTA plumbing. The same firmware is shared with three other robot designs, so what you learn on TARS carries over to them. It also makes a reasonable teaching platform for showing how a modern voice assistant is split between on-device wake-word detection and cloud speech and LLM services.
What it replaces or enables: Hackster says the mechanical designs and documentation are released alongside the firmware, so the remaining work is printing and assembly rather than designing motion control and display drivers from nothing. Firmware that already has ST7789V2, QMI8658C and SCS-series servo support on ESP32-S3 may also be worth studying on its own, depending on how the licensing question is resolved.
What to keep in mind: the price covers electronics only, so add your own filament and print time. Conversation depends on network services the sources don't fully identify. The sources we checked don't list battery details. Returns aren't accepted once an order ships.
Price and availability: US$99.00 on the LuwuDynamics shop, listed in stock as of November 15, 2026, shipping within 10 days of payment.